Panasonic Quiet KX-P2123 24-pin Dot Matrix Form Printer

Discussion:

(too old to reply)

aelover77

2009-03-05 03:22:44 UTC

I _FOR_SURE_ ordered this printer and from what I am understanding the
driver is built in my windows Vista system. Does this mean when it gets
here I should just be able to plug it in and it will be picked up or???
I also run a HP Photosmart C6280 on my main desktop computer....can both
printers be hooked up or could I hook up the dot matrix to my lap top (
which also has vista )

--
aelover77

Alan Morris [MSFT]

2009-03-05 17:47:58 UTC

Permalink

make sure the laptop has a parallel port for the Forms printer.
--
Alan Morris
Windows Printing Team
Search the Microsoft Knowledge Base here:
http://support.microsoft.com/search/?adv=1

This posting is provided "AS IS" with no warranties, and confers no rights.

Post by aelover77
I _FOR_SURE_ ordered this printer and from what I am understanding the
driver is built in my windows Vista system. Does this mean when it gets
here I should just be able to plug it in and it will be picked up or???
I also run a HP Photosmart C6280 on my main desktop computer....can both
printers be hooked up or could I hook up the dot matrix to my lap top (
which also has vista )
--
aelover77

Andrew Rossmann

2009-03-05 21:47:07 UTC

Permalink

I don't know if it's Plug-and-Play, probably not.

To install the drivers: Go to the Control panel, then pick Printers.

Near the top (below the menu bar, above the icons), pick 'Add a
printer'.

Choose 'Add a local printer'

For the port, use LPT1:

On the driver selection, choose Panasonic on the left, and KX-P2123 on
the right.

--
If there is a no_junk in my address, please REMOVE it before replying!
All junk mail senders will be prosecuted to the fullest extent of the
law!!
http://home.att.net/~andyross

Tom Ferguson

2009-03-06 07:57:14 UTC

Permalink

In all probability, your desktop computer has a parallel port. If so, there
would be no problem connecting the Panasonic printer to it. If the printer
gives garbled output, check the port settings in the BIOS and try setting to
SPP (Simple Parallel Port), if that setting is available.

I do not foresee any problem connecting both printers to your desktop
computer. In fact, once set up, you can send jobs to each independently.

I don't know of any recent notebook/laptops that have a parallel port.
However, I really have not done any kind of survey. If you want to connect
the Panasonic to the notebook, you could use a parallel to USB converter.
Also, there are parallel to express card devices such as these-
http://www.cooldrives.com/1ppaspex34.html

Or you could do it through your network (your message seems to imply that
you have one).

Good luck.
--
Tom
MSMVP 1998-2007

aelover77

2009-03-06 19:55:27 UTC

Permalink

Ahhh so I received it and have had nothing but a head ache and a hal
from it and dont know what to do
So i got a Dot Matrix Panasonic KX P2123 for my computer. My use o
this is for tatoo stencils in which you dont need the ribbon and such
But I just got it todayand went to hook it up to my computer and hooke
it up with a parallel/USB cord. Once I did so, I went to add printer
and added it just fine, automatically had the driver installed. Which
was trilled about

Then I went to print a test page as prompted with adding a printer an
got nothing
Then I tried from photoshop. Nothing. And from irfan view. Nothing. I
the buffer it says error. I cant seem to figure out what I am doin
wron

--
aelover77

Alan Morris [MSFT]

2009-03-06 21:08:10 UTC

Permalink

Is the printer in the printers folder

If not make sure the spooler service is started.

If the machine is x64, try to print using the x64 version of notepad.
--
Alan Morris
Windows Printing Team
Search the Microsoft Knowledge Base here:
http://support.microsoft.com/search/?adv=1

This posting is provided "AS IS" with no warranties, and confers no rights.

Ahhh so I received it and have had nothing but a head ache and a half
from it and dont know what to do.
So i got a Dot Matrix Panasonic KX P2123 for my computer. My use of
this is for tatoo stencils in which you dont need the ribbon and such.
But I just got it todayand went to hook it up to my computer and hooked
it up with a parallel/USB cord. Once I did so, I went to add printer,
and added it just fine, automatically had the driver installed. Which I
was trilled about!
Then I went to print a test page as prompted with adding a printer and
got nothing.
Then I tried from photoshop. Nothing. And from irfan view. Nothing. In
the buffer it says error. I cant seem to figure out what I am doing
wrong
--
aelover77

nickstyle

2009-07-13 15:40:58 UTC

Permalink

Hello, today I bought the same model and I have same problem.i wanna
use it for the stencil tattoo to.Tell me please if you solved th
problem and how.How make stencile?
Regard

--
nickstyl
-----------------------------------------------------------------------
nickstyle's Profile: http://forums.techarena.in/members/114330.ht
View this thread: http://forums.techarena.in/vista-print-fax/1135043.ht

http://forums.techarena.i

Tom Ferguson

2009-07-13 18:17:26 UTC

Permalink

one way-

Post by nickstyle
Hello, today I bought the same model and I have same problem.i wanna
use it for the stencil tattoo to.Tell me please if you solved the
problem and how.How make stencile?
Regards
--
nickstyle
------------------------------------------------------------------------
nickstyle's Profile: http://forums.techarena.in/members/114330.htm
View this thread: http://forums.techarena.in/vista-print-fax/1135043.htm
http://forums.techarena.in

j***@gmail.com

2013-10-26 20:09:58 UTC

Permalink

I have the same problem here. Did you solve it?

Regards,
Juan